Checklist before starting the high-pressure pump-Jinpu (Tianjin) Pump Industry Co., Ltd.

Checklist before starting the high-pressure pump


release time:

2026-08-31

General technical specifications; The specific parameters, structure, and instal

General technical specifications; The specific parameters, structure, and installation requirements shall be subject to the corresponding product manual and actual working condition verification.

Answer directly

QQ_1788167896246.png

Before starting, confirm that the equipment is in a safe state: the protective cover, fasteners, base, coupling or belt are intact; High pressure hoses, fittings, spray guns, and nozzles are undamaged; The safety valve, pressure regulating valve, and pressure gauge are installed correctly. Check the oil level and quality of the crankcase, and confirm whether the transport oil plug has been replaced with a working oil plug with a ventilation structure during the first use.

Key technical specifications

Check water supply: clean water source, sufficient liquid level, clean filter, fully open inlet valve, suction hose not deflated, joint not leaking, medium temperature within allowable range. Confirm that the bypass or unloading circuit is unobstructed and the outlet valve position is correct. Automatic equipment should also be tested for low liquid level, low inlet pressure, emergency stop, and protective interlock.

After the initial start-up or maintenance, the air should be exhausted in a low pressure state, and the rotation direction should be confirmed by jogging before gradually increasing the speed and loading. Observe pressure gauge, current, noise, vibration, pump head leakage, and return water temperature. If the pressure cannot be stably established, do not repeatedly tighten the pressure regulating valve. Stop the machine to check the water supply, valve group, nozzle, and seal.

Pre launch checklist

Liquid supply side

The water tank level, water supply flow rate, and temperature meet the requirements;

The filter is clean and has sufficient flow capacity;

The inlet pipeline is short, the seal is reliable, and there is no folding or leakage;

The pump chamber and inlet pipeline have been filled with liquid and can be vented.

Pump and Drive

The oil level, oil product, and breathing/transportation plug status comply with the manual;

Couplings, belts, fasteners, and protective covers are intact;

After the first wiring or maintenance, the rotation direction has been checked by tapping;

Motor protection, grounding, and emergency stop are effective.

high-voltage side

Hoses, hard tubes, fittings, spray guns, and nozzles are undamaged;

The installation of pressure regulating/unloading and safety valves is correct;

The range and status of the pressure gauge are suitable;

There is no sealed or pressure relief protection at the exit.

Do not start

When there is no water or uncertain water supply, high-pressure hose bulging, oil emulsion, loose pump body, unclear rotation direction, missing protective cover, or safety valve isolated, it shall not be started.

Frequently Asked Questions

Can the pump be run dry for a short period of time to check the rotation direction?

Dry spinning should be avoided. Use the manufacturer approved jogging and filling methods to verify the rotation direction.

Do you need further selection or diagnosis?

Complete working conditions can be submitted through the CENTSEA official website. When there is insufficient information, fill in the measurement and operation records first, and do not directly guess the model or faulty parts.

The first start-up also requires checking the transportation status

Some pumps use transport sealing oil plugs when they leave the factory. Before formal operation, they must be replaced with working oil plugs with ventilation function according to the instructions, otherwise the crankcase pressure may be abnormal.

Before starting, it should be confirmed that the inlet valve is open, the pump chamber is reliably supplied with liquid, and the air is exhausted in the unloading or low-pressure state.

The inlet pressure gauge, outlet pressure gauge, and motor current should establish a baseline at the first start-up for subsequent maintenance comparison.

For the first power on, it is advisable to check the rotation direction by tapping. If there is a leak, abnormal noise, strong vibration, or abnormal current in the high-pressure pipeline, the machine should be stopped immediately, the pressure should be relieved, and the cause should be eliminated.

Engineering Tips

Make the checklist into a signed record, distinguishing between "each shift", "first start-up after maintenance", and "start-up after long-term shutdown", which is more reliable than verbal handover.

This article explains general technical principles. If specific equipment needs to be implemented, please check the corresponding product data sheet based on working pressure, flow rate, medium, temperature, liquid supply conditions, and operating system. Jinpump can assist in organizing selection inputs based on complete operating conditions, but the specific model and parameters should be based on the final confirmed data.


label:



If you wish to learn more detailed information about Jinpu Company, please visit our official website, where comprehensive and in-depth information is available for your reference!


Copyright © Jinpu (Tianjin) Pump Industry Co., Ltd. All rights reserved

Leave your message

If you have any suggestions or questions for us, please feel free to contact us!

We use cookie to improve your online experience. By continuing to browse this website, you agree to our use of cookie.

Cookies

Please read our Terms and Conditions and this Policy before accessing or using our Services. If you cannot agree with this Policy or the Terms and Conditions, please do not access or use our Services. If you are located in a jurisdiction outside the European Economic Area, by using our Services, you accept the Terms and Conditions and accept our privacy practices described in this Policy.
We may modify this Policy at any time, without prior notice, and changes may apply to any Personal Information we already hold about you, as well as any new Personal Information collected after the Policy is modified. If we make changes, we will notify you by revising the date at the top of this Policy. We will provide you with advanced notice if we make any material changes to how we collect, use or disclose your Personal Information that impact your rights under this Policy. If you are located in a jurisdiction other than the European Economic Area, the United Kingdom or Switzerland (collectively “European Countries”), your continued access or use of our Services after receiving the notice of changes, constitutes your acknowledgement that you accept the updated Policy. In addition, we may provide you with real time disclosures or additional information about the Personal Information handling practices of specific parts of our Services. Such notices may supplement this Policy or provide you with additional choices about how we process your Personal Information.


Cookies

Cookies are small text files stored on your device when you access most Websites on the internet or open certain emails. Among other things, Cookies allow a Website to recognize your device and remember if you've been to the Website before. Examples of information collected by Cookies include your browser type and the address of the Website from which you arrived at our Website as well as IP address and clickstream behavior (that is the pages you view and the links you click).We use the term cookie to refer to Cookies and technologies that perform a similar function to Cookies (e.g., tags, pixels, web beacons, etc.). Cookies can be read by the originating Website on each subsequent visit and by any other Website that recognizes the cookie. The Website uses Cookies in order to make the Website easier to use, to support a better user experience, including the provision of information and functionality to you, as well as to provide us with information about how the Website is used so that we can make sure it is as up to date, relevant, and error free as we can. Cookies on the Website We use Cookies to personalize your experience when you visit the Site, uniquely identify your computer for security purposes, and enable us and our third-party service providers to serve ads on our behalf across the internet.

We classify Cookies in the following categories:
 ●  Strictly Necessary Cookies
 ●  Performance Cookies
 ●  Functional Cookies
 ●  Targeting Cookies


Cookie List
A cookie is a small piece of data (text file) that a website – when visited by a user – asks your browser to store on your device in order to remember information about you, such as your language preference or login information. Those cookies are set by us and called first-party cookies. We also use third-party cookies – which are cookies from a domain different than the domain of the website you are visiting – for our advertising and marketing efforts. More specifically, we use cookies and other tracking technologies for the following purposes:

Strictly Necessary Cookies
These cookies are necessary for the website to function and cannot be switched off in our systems. They are usually only set in response to actions made by you which amount to a request for services, such as setting your privacy preferences, logging in or filling in forms. You can set your browser to block or alert you about these cookies, but some parts of the site will not then work. These cookies do not store any personally identifiable information.

Functional Cookies
These cookies enable the website to provide enhanced functionality and personalisation. They may be set by us or by third party providers whose services we have added to our pages. If you do not allow these cookies then some or all of these services may not function properly.

Performance Cookies
These cookies allow us to count visits and traffic sources so we can measure and improve the performance of our site. They help us to know which pages are the most and least popular and see how visitors move around the site. All information these cookies collect is aggregated and therefore anonymous. If you do not allow these cookies we will not know when you have visited our site, and will not be able to monitor its performance.

Targeting Cookies
These cookies may be set through our site by our advertising partners. They may be used by those companies to build a profile of your interests and show you relevant adverts on other sites. They do not store directly personal information, but are based on uniquely identifying your browser and internet device. If you do not allow these cookies, you will experience less targeted advertising.

How To Turn Off Cookies
You can choose to restrict or block Cookies through your browser settings at any time. Please note that certain Cookies may be set as soon as you visit the Website, but you can remove them using your browser settings. However, please be aware that restricting or blocking Cookies set on the Website may impact the functionality or performance of the Website or prevent you from using certain services provided through the Website. It will also affect our ability to update the Website to cater for user preferences and improve performance. Cookies within Mobile Applications

We only use Strictly Necessary Cookies on our mobile applications. These Cookies are critical to the functionality of our applications, so if you block or delete these Cookies you may not be able to use the application. These Cookies are not shared with any other application on your mobile device. We never use the Cookies from the mobile application to store personal information about you.

If you have questions or concerns regarding any information in this Privacy Policy, please contact us by email at . You can also contact us via our customer service at our Site.